Not, remove the tray cover, eject the disk and advance the wheelĪnother 1/8 turn and repeat the process. If all three loaded successfully, congratulations you're finished. If the DVD loads, eject itĪnd load a silver backed disk, if that loads try a purple backed disk. Wait to see if the DVD loads, you may have to use theīrowser in order to load each disk you test. Order to close the tray and load the DVD (hold down the cover asĮxplained above). Need to hold down the cover with your fingers while trying to load/testĪ disk) Now place a DVD in the tray and press the eject/close button in The tray cover back down in order to test the machine you will only Then advance the wheel about 1/8 of a turn and place the disk Works, put the wheel back to the original position that you have To zero, after it reaches the maximum angle it will go back to flatĪfter each full rotation. It will only alter the angle a few degrees before it goes back Wheel for a few full rotations in order to see how it changes theĪngle. position has been marked, feel free to spin the That way you will always know the original position that the wheel was Take aįelt-tip marker and mark the point on the wheel that meets the tab. That there is a small metal tab that holds the wheel in place. This wheel changes the angle in which the disk is held. White, geared wheel about the size of a quarter. At the back of the unit you should see a small Press the eject button so that the tray slides forward exposing Three.) It will be necessary to have the unit powered up to perform the One with a purple back in order to fine tune the system to play all You should have a DVD, a game disk with a silver or gold back and Needs to be hooked up to a TV as well to test it while you have it Has been cleaned you will need to plug the unit back in, (The unit After the cover is off of the disk tray and the laser It to dry on its own, making sure that no lint was left behind from the Off, the first thing to do is to clean the laser eye. Tray, this will require a rather small phillips screwdriver (I've seenĪ few that use a standard slotted screw). Once the outer cover is off you need to remove the cover to the disc Sensitive as it appears just remove the tape holding the ribbon cable. Usually taped to the top of the disc tray. Small metallic ribbon cable inside the machine leading to theĮject/close and reset buttons on the front of the unit, this cable is As you remove the outer cover you will notice a Towards the front in order to clear the controller jacks and theĮject/close buttons. To remove the outer cover, lift up from the rear of the unit and pull Remove all the screw covers from the bottom of the unit, both plasticĪnd rubber, these will be the only screws you will have to remove in If you haven't done this before, you will have to First take off the outerĬover of you PS2. So you'll be familiar with the entire process. The instructions all the way through before you attempt the repair just You're going to be surprised when you find out how easy this is. probably your game console has problems on disk reading. if it can, then theres nothing wrong with the cd. If you don't see the code you want on this page I recommend you return to my Champions: Return To Arms Codebreaker Codes index page and choose a different section.SOURCE: God of War 1 and 2(Unable to read disc)!Ĭheck your cd if it can play in different ps2 consoles. This will explain how to setup and use the codes on this page with that emulator.Īlternatively if you're playing on a physical console you'll need to own a CodeBreaker/GameShark disc in order to use these codes. If you're playing with the PCSX2 Emulator and you'd like to use the codes on this page I recommend heading over to my How To Use Cheat Codes on PCSX2 Guide. This page contains all of the CodeBreaker cheat codes I have for Champions: Return To Arms (NTSC-U). Champions: Return To Arms - Player 1 Codebreaker Codes (NTSC-U)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |